Testing
How to read the HPLC chromatogram and mass spec data on a peptide COA
A buyer's guide to peptide COA raw data: retention time, peak table and area %, observed vs expected mass, m/z, charge states, and common mismatches.
A COA headline such as “99.1% purity, identity confirmed” is a summary of two data sets: an HPLC chromatogram and a mass spectrum. This guide shows professional buyers how to check that the summary matches the data underneath it, and what to request when it does not.
This article is for wholesalers, brands, and laboratory procurement teams who already have a report in hand. It is educational procurement guidance, not medical, legal, or end-use advice, and it is not a method for preparing or handling material.
What HPLC and mass spec each answer (and what neither answers)
Read the two techniques as separate questions. HPLC answers a relative-purity question under one method. Mass spectrometry answers whether the observed mass is consistent with the mass expected for the named sequence. Neither result answers the other question, or several other questions buyers often hope a COA will settle.
| Data on the report | What it can support | What it does not answer |
|---|---|---|
| HPLC chromatogram and peak table | Relative purity as an area % under the stated method | Whether the main peak is the named peptide; how many milligrams are in a vial |
| Mass spectrum (observed vs expected mass) | Whether the measured mass is consistent with the target, within the laboratory’s stated tolerance | How pure the sample is; content per vial |
| Neither data set, on its own | — | Net peptide content, sterility, endotoxin, or a link to the lot you will receive |
That is why a high HPLC percentage cannot prove identity, and a matching mass cannot prove purity. A sample can show a clean main peak of an unexpected species, or a correct mass sitting next to other peaks that were never integrated. For the wider test panel, see five common peptide tests and what each answers. For why purity is not content, see 99% peptide purity does not mean the vial contains the labeled amount. The files that usually travel with a report are described in the peptide documentation package. For the field-by-field buyer checklist around this data, see How to read a peptide COA.
Reading an HPLC chromatogram step by step
The figures and peak table below are an illustrative example, not a laboratory report. Do not treat the numbers as results for any product or lot.
The axes: retention time and detector signal
The horizontal axis is retention time, usually in minutes: how long after the sample is introduced a peak is detected. The vertical axis is the detector signal, often in milli-absorbance units (mAU) for a UV detector. The baseline and the integrated time window matter as much as the tallest peak.
The main peak and the impurity peaks
The main peak is the largest integrated peak assigned to the target. Smaller peaks in the same window may be related substances or other detected components. A disturbance at the start of the run is often a solvent front; whether it is integrated depends on the method and should be stated. A visually “single” peak is not, on its own, a purity result. The result comes from the peak table.
The peak table: how area % becomes the purity figure
Purity by HPLC is typically:
Area % of the main peak = (main peak area ÷ total integrated peak area) × 100
Using the illustrative table:
| Peak | Retention time (min) | Area | Area % |
|---|---|---|---|
| Impurity 1 | 6.10 | 520 | 0.52 |
| Main peak | 8.42 | 99,100 | 99.10 |
| Impurity 2 | 9.80 | 380 | 0.38 |
| Total | — | 100,000 | 100.00 |
The headline figure should be 99.10% (often rounded to 99.1%). Recalculate it yourself. If the result does not match the reported percentage, or if the listed area percentages do not add to 100% after ordinary rounding, ask how peaks were selected and whether any were excluded (for example, a solvent front). Do not “correct” the number yourself.
Public summaries of USP General Chapter <621> Chromatography describe chromatographic methods as procedures with stated conditions, and treat system suitability as part of method control. A relative retention time printed on a report may be informational only. Retention time on its own does not prove identity. That would require comparison with a reference material under the same method conditions, or a separate identity method such as mass spectrometry.
Method details that should be printed
A chromatogram is hard to interpret if the method is not stated. Look for:
- Column (stationary phase, dimensions, particle size, if given)
- Mobile phase or gradient
- Detection wavelength (or detector type)
- Amount or concentration applied to the column, if stated
- Integration rules: start and end times, and whether the solvent front is included
If those details are missing, ask for them, or for the original data file, before relying on the headline percentage.
Reading a mass spectrum on a peptide COA
The spectrum and arithmetic below are also an illustrative example, not a laboratory report.
Expected (theoretical) mass vs observed mass
The expected mass is calculated from the peptide sequence. The observed mass is derived from the spectrum. Compare them on the same basis: monoisotopic with monoisotopic, or average with average. Mixing the two bases can create an apparent mismatch that is only a unit inconsistency.
m/z and charge states: converting to neutral mass
A mass spectrum plots intensity against mass-to-charge ratio (m/z), not against neutral mass. Peptides often carry more than one proton, so one molecule can appear as several peaks (for example, 2+ and 3+). For a protonated ion [M+zH]z+, a common conversion is:
M = z × (m/z) − z × 1.00728
The subtraction term is the proton mass, rounded to 1.00728 from the CODATA value for the proton mass in u (1.0072764665789 u; retrieved 10 November 2026).
Illustrative conversion, using the 2+ peak at m/z 710.86 and an expected monoisotopic mass of 1419.70:
- z × (m/z) = 2 × 710.86 = 1421.72
- z × 1.00728 = 2.01456
- M = 1421.72 − 2.01456 = 1419.70544, which rounds to 1419.71
The difference from 1419.70 is about 0.01 Da, or about 4 ppm relative to the expected mass. Whether that is “a match” depends on the tolerance the laboratory states for this instrument and method — not on a buyer rule of thumb. This formula applies to protonated ions. Sodium, potassium, or other adducts need a different correction. If extra peaks are labelled as adducts, ask the laboratory to explain them; do not reassign peaks yourself.
Tolerance: what “a match” means on this instrument
High-resolution instruments often state tolerance in parts per million (ppm). Lower-resolution instruments often use daltons (Da). Use the tolerance printed on the report or in the method. A difference inside that window supports the identity claim as the laboratory defined it. A difference outside it is a reason to ask for an explanation or the raw file, not a reason to declare the report false.
Adducts and extra peaks you may see
Spectra may show [M+Na]+, [M+K]+, or other adducts, or more than one charge state of the same molecule. Their presence is not, by itself, a verdict. Ask the laboratory which peak was used for the reported observed mass, and how any additional peaks were interpreted. If the report only says “MS: conforms” and gives no mass values, charge state, or tolerance, ask for those values, or for the spectrum, before relying on the identity line.
When the headline and the data disagree: a mismatch table
Use the table as a list of questions, not as a verdict sheet. Where a figure and the underlying data disagree, ask for an explanation or the original data file, and hold payment decisions until the discrepancy is resolved in writing. For document-level authenticity checks (lookup, recycled files, borrowed reports), see Fake peptide COA: how to spot an edited, borrowed or recycled report.
| What you see | What it may mean | What to ask for |
|---|---|---|
| A purity percentage with no chromatogram or peak table | The headline cannot be recalculated | The chromatogram, the peak table, and the integration rules |
| Recalculated area % does not match the reported purity | Rounding, excluded peaks, or a transcription issue | A written explanation of which peaks were integrated, and the original data file |
| A clear second peak on the trace, but the report describes a single high-purity peak | An unintegrated peak, a different time window, or a copy that does not match the data | The peak table for the same run, and confirmation that the figure belongs to this chromatogram |
| “MS conforms” or “identity confirmed” with no mass values | A conclusion without supporting numbers | Observed mass, expected mass, charge state, stated tolerance, or the spectrum |
| Observed mass differs from expected mass by more than the laboratory’s own tolerance | A unit mismatch (monoisotopic vs average), an adduct, or a result that needs review | Confirmation of the mass basis, the peak used, and a written explanation |
| Sample ID or date on the chromatogram or spectrum does not match the report cover | The supporting figure may belong to a different run | The data file that belongs to this report ID and date |
| The same chromatogram appears on reports for different products or lots | The figure may have been reused | The original data file for each report, and a laboratory-side lookup of each record |
What these data still cannot tell you about your order
Even when the chromatogram and the spectrum support the headline, the results describe the sample that was submitted. They do not automatically describe the lot you will receive, and they do not measure net peptide content per vial. Content needs a separate quantitative method.
To connect HPLC and MS results to an order, lot marks on the report, labels, packing list, and invoice need to match in writing. Absent that correspondence, the correct working label is Tested Sample, not Batch-Linked. See Tested Sample vs Batch-Linked COA and what a COA proves, and what it does not. If you need a higher level of assurance for a specific delivery, you can take a sample from the goods you received and commission a laboratory yourself.
ICH quality guidelines Q6A and Q6B, listed on the ICH quality guidelines page, treat a specification as a set of test procedures and acceptance criteria. A COA is easier to read when the written order states which methods and limits apply.
See real records with their scope labelled
Public records in the COA library show the product, date, specification, Tested Sample scope, and status (for example, Current or Historical) on each entry. Public copies are redacted. Qualified buyers can request a controlled full-version verification against a BatchVerity report ID. That process checks the report record. It does not approve goods or convert a Tested Sample record into a Batch-Linked one.
Complimentary preliminary review
Send the report and your product requirement. We will point out which data are missing and what to request before payment. This is a reading of the document against your written specification — not an approval, clearance, or authenticity guarantee.
Request a review through an RFQ, or contact us on WhatsApp at +86 180 0545 5057.
— Leo Wang, BatchVerity
FAQ
How do you read HPLC purity on a peptide COA?
Find the peak table under the chromatogram. Purity by HPLC is the main peak’s area divided by the total integrated peak area, multiplied by 100. Check that the reported percentage matches that calculation and that the method, wavelength, and sample ID are printed.
Does HPLC purity confirm the peptide’s identity?
No. HPLC shows how much of the detected signal sits in the main peak. It does not show what that peak is. Identity is normally supported by mass spectrometry, comparing the observed mass with the mass expected from the sequence.
What does m/z mean on a peptide mass spec report?
m/z is mass divided by charge. Peptides often carry more than one charge, so a spectrum can show several peaks for one molecule. Neutral mass is calculated as M = z × (m/z) − z × 1.00728, then compared with the expected mass.
How close should observed and expected mass be?
Close enough to fall within the tolerance the laboratory states for its instrument and method, usually expressed in ppm for high-resolution instruments or in daltons for lower-resolution ones. Compare like with like: monoisotopic with monoisotopic, average with average.
Is a COA that says “MS conforms” without numbers enough?
It is a conclusion without the evidence. Ask for the observed mass, the expected mass, the charge state used, and the stated tolerance, or the spectrum itself.
Do good HPLC and MS results prove the amount in each vial?
No. Neither measures net peptide content per vial. Content needs a separate quantitative method, and the result applies to the tested sample unless lot linkage is documented.
What should I do if the chromatogram and the headline number disagree?
Do not draw a conclusion yourself. Ask the supplier or laboratory for the original data file and an explanation, and hold payment decisions until the discrepancy is resolved in writing.
Sources
Pages retrieved 10 November 2026 (Asia/Shanghai).
- NIST, CODATA value: proton mass in u: https://physics.nist.gov/cgi-bin/cuu/Value?mpu
- USP, FAQs: <621> Chromatography: https://www.usp.org/frequently-asked-questions/chromatography
- USP–NF, General Chapter <621> Chromatography (public chapter page): https://doi.usp.org/USPNF/USPNF_M99380_10_01.html
- ICH, Quality Guidelines (including Q6A and Q6B on test procedures and acceptance criteria): https://www.ich.org/page/quality-guidelines
Scope note (retain on publish)
This article is educational procurement guidance for professional buyers. It is not medical, legal, or regulatory advice. It does not publish test results for any product and does not approve, clear, or certify goods for any human use. No dosing, therapeutic, safety, or benefit claims are intended.